Every Tuning bench needs a strong set of vices to keep the board secure during edging and waxing sessions. Our snowboard-specific version utilizes suction grips to keep the board horizontally secure during waxing or scraping, while also providing a vertically stable slide-in setup for sharpening edges. Portable and packable enough for road trips with a design that mounts easily to any bench or table, the vices also hide a bottle opener to make two-beer tasks in the Tuning room easier.
RaceWax Ski Wax Brush Kit Snowboard Set of Three, Nylon - HorseHair - Brass
New, improved set for 2016. All the brushes (3 in x 4.5 in) you need to get started. This money saving three brush kit contains: A brass brush (10 mm) for renewing base structure, opening pores before you wax (for this step brush in the opposite direction - tail to tip), and brushing hard waxes.A nylon brush (10 mm) that is the workhorse of wax removal. Designed to be stiff enough to remove wax in less passes to save you time.A soft, fine horsehair brush (8 mm) for removing wax from the fine structure of your base for the ultimate polish!Handy zippered storage case included. Each brush measures 3 in x 4.5 in.
VOLA Side Bevel File Guide Tuning Winter Sports Tool Ski and Snowboard Pocket Edge Tuner 88 Degress and 89 Degress
Perfect for a lower cost ski base edge tool to work well and help you get a best sharpening result. The sides will like a new from the factory. Before you start mark the side edge with a sharpie, start the tool at the lowest angle and see if it removes the marking on your edge. Raise the angle step-wise and repeat until it removes the mark. That is your angle.
RaceWax Quick Tune Ski Snowboard Wax Tuning KitWill tune both skis and snowboards!Edge Beveler for 88 / 90 side edge angles;Two-sided metal cutting file included with edge tool;40 g bar of our best quality All Temperature Wax (enough for about 2-4 waxings);5.5 inch, 4-mm thick precision ground Triangle Wax Scraper with a corner notch for edge cleaning;Brass file brush;Metal Scraper with vinyl storage sleeve;One Clear P-Tex (8 mm diameter, about 190 mm long (7.5 inches) long);One Black P-Tex (8 mm diameter, about 190 mm long (7.5 inches) long);Two Brake Retainers;Non-abrasive Fibertex pad for buffing after scraping waxall in a zippered Cordura pouch with lots of storage pockets.
Don?t go inside just because your battery runs out on your foot warmers The Hotronic S4 Boot Heater Spare Battery Pack will give you hours of additional life on your Hotronic boot heaters Keep these spare batteries in your pockets and swap them out mid day to keep enjoying Mother Nature with toasty toes Duration Range Setting 1 16 5 ? 19 5 hours at an average temperature of 84F 95FSetting 2 7 ? 9 25 hours at an average temperature of 107F 118FSetting 3 5 ? 6 5 hours at an average temperature of 122F ? 132FSetting 4 2 5 ? 4 hours at an average temperature of 156F ? 168F Features Designed as a replacement battery pack for the Hotronic S4 Custom Boot Heaters Battery pack is easily securable to footwear
OneBall Jay Ski/Snowboard Tune Kit With Waxing Iron and Wax
Manufacturer: One Ball Jay
Brand: One Ball Jay
ITS NOT THAT HARD! - Waxing your gear is one of the easiest things that you can do to increase the performance of your board or skis. Waxing makes your equipment easier to control, thus it glides much better, increasing both your speed and the ease of turning. IE- you don't get as tired. Second, Waxing prolongs your equipments "useful life" since waxed bases are more resistant. Consequently, you get the most from your Snowboard or skis. And lastly when you blow by your buddys not only on the slope but on all the all important cat-tracks you'll truly understand why the pro's wax every session.The One Ball Jay Iron's 12v 13cm X 11cm base has a beveled edge with adjustable heat settings and will heat evenly without damaging your base-stop stealing moms clothes iron and use the right tool for the right job!
Tools4Boards Hone diamond stones feature premium Swiss-made diamond fabric mounted on exceptionally flat precision milled stainless steel backer. Polishing and deburring ability of a stone combined with the cutting ability of a file. Stainless steel backer dampens vibration better than conventional plastic or aluminum backers providing superior feel. Perfect for touching up edges and removing burrs on-hill or to smooth and polish edges after filing. For best results immerse stone in a glass or ceramic mug consisting of 50% water and 50% rubbing alcohol when in use and scrub with an old tooth brush to remove swarf build-up. Place in a file holder or on an edge guide to maintain accurate edge bevel angles.