RaceWax Ski Wax Brush Kit Snowboard Set of Three, Nylon - HorseHair - Brass
New, improved set for 2016. All the brushes (3 in x 4.5 in) you need to get started. This money saving three brush kit contains: A brass brush (10 mm) for renewing base structure, opening pores before you wax (for this step brush in the opposite direction - tail to tip), and brushing hard waxes.A nylon brush (10 mm) that is the workhorse of wax removal. Designed to be stiff enough to remove wax in less passes to save you time.A soft, fine horsehair brush (8 mm) for removing wax from the fine structure of your base for the ultimate polish!Handy zippered storage case included. Each brush measures 3 in x 4.5 in.
Don?t go inside just because your battery runs out on your foot warmers The Hotronic S4 Boot Heater Spare Battery Pack will give you hours of additional life on your Hotronic boot heaters Keep these spare batteries in your pockets and swap them out mid day to keep enjoying Mother Nature with toasty toes Duration Range Setting 1 16 5 ? 19 5 hours at an average temperature of 84F 95FSetting 2 7 ? 9 25 hours at an average temperature of 107F 118FSetting 3 5 ? 6 5 hours at an average temperature of 122F ? 132FSetting 4 2 5 ? 4 hours at an average temperature of 156F ? 168F Features Designed as a replacement battery pack for the Hotronic S4 Custom Boot Heaters Battery pack is easily securable to footwear
OneBall Jay Ski/Snowboard Tune Kit With Waxing Iron and Wax
ITS NOT THAT HARD! - Waxing your gear is one of the easiest things that you can do to increase the performance of your board or skis. Waxing makes your equipment easier to control, thus it glides much better, increasing both your speed and the ease of turning. IE- you don't get as tired. Second, Waxing prolongs your equipments "useful life" since waxed bases are more resistant. Consequently, you get the most from your Snowboard or skis. And lastly when you blow by your buddys not only on the slope but on all the all important cat-tracks you'll truly understand why the pro's wax every session.The One Ball Jay Iron's 12v 13cm X 11cm base has a beveled edge with adjustable heat settings and will heat evenly without damaging your base-stop stealing moms clothes iron and use the right tool for the right job!
The Wintersteiger Sport Plus vise is a newly designed vise for tuning all types and shapes of skis.Features sturdy, high-tensile aluminum body.Light and easy to transport.The new holding system keeps the ski secure for base and side edge work.Positioning system allows for 0, 60 and 90 degree mounting.Special rubber suction cups provide better hold.Includes strap to attach ski bindings to the center clamp.Includes two brake retainers.
Complete Edge Care Kit Base-Side Ski Angle Tool +3 diamonds +Gummi stone
Complete Edge Care Kit - Everything you need to professionally sharpen ski and snowboard edges.Side and base edge bevel multi tool (does all angles) and includes a metal file with three DMT diamond stones and a deburring gummi stone.This one tool is all you need to sharpen and bevel your edges. Dial a precise angle from 0 degree to 5 degrees in 0.5 degree increments. Does every angle imaginable!Metal file included!One Gumi or Gummi Stone, may be red or gray, for prepping an edge, deburring as the final step in edge sharpening, or detuning.Three diamond stones included: Use the black for cutting, the blue to maintain the sharpness and the red to fine sharpen and polish.Bonus Benefit for this tool: If you don't know what base and side angles your ski/board are set to, this tool can help you find them. Before you start mark the metal edge with a sharpie, start the tool at the lowest angle and see if it removes the marking on your edge. Raise the angle step-wise and repeat until it removes the mark. That is your angle! Record the base/side angles for future reference.There are two ways to determine the cutting direction for the metal file in the tool: (a) you can run the back of your fingernail across the file. Your fingernail will run smoothly one way and the other way (the cutting direction) will produce small shavings from your fingernail on the file; or, (b) look closely at the file with a magnifying glass. You will see that the file teeth point in only one direction. You pull the file in the direction that will cause the most friction against the ski edge (the cutting direction).
Base-Side Bevel File Guide SKS Multi Tool with 3 DMT diamond stones
Side and base edge bevel multi tool with three DMT diamond stones and includes a metal file.This one tool is all you need to sharpen and bevel your edges. Dial a precise angle from 0 degree to 5 degrees in 0.5 degree increments.Three diamond stones included!Use the black for cutting, the blue to maintain the sharpness and the red to fine sharpen and polish.Bonus Benefit for this tool: If you don't know what base and side angles your ski/board are set to, this tool can help you find them. Before you start mark the metal edge with a sharpie, start the tool at the lowest angle and see if it removes the marking on your edge. Raise the angle step-wise and repeat until it removes the mark. That is your angle! Record the base/side angles for future reference.
After the wax has cooled to room temperature any excess must be scraped off and the structure must be brushed. Alway allow the wax and ski or snowboard to cool to room temperature before scraping, otherwise the warm wax will be pulle from the pores leaving the base dry.